BWS Industrial Services Inc.
Call BWS Industrial Services Inc.
484 - 415 - 9063

Pioneer Dock Equipment Dealer

Pioneer Dock Equipment Dealer

Pioneer Dock Equipment manufactures and distributes a wide range of loading dock equipment. Pioneer is centrally located in Spring Hill, Tennessee,

Pioneer provides a full line of high quality, durable dock products and has developed an enviable reputation for dealer support, customer responsiveness, and personal service.


Pioneer FAQ's

1. Which applications require fully hydraulic rather than mechanical Dock Levelers? Both types are available in a variety of sizes and capacity ranges. Hydraulic Dock Levelers, although higher in initial cost, have proven to provide lower lifetime cost due to lower maintenance requirements. Added benefits of fully hydraulic Dock Levelers include smooth, quiet operation at the touch of a button and automatic return to cross traffic position. For operator convenience and years of trouble-free service, fully hydraulic Dock Levelers are suggested for all applications.

2. Talking about capacity, I’ve heard the terms STATIC, ROLLOVER and DYNAMIC being used. Which rating should influence my Dock Leveler selection? Static and rollover refer to the amount of weight that a Dock Leveler can safely support, either stacked on the deck or crossing over it, while in the stored position. Dynamic capacity refers to the total force of a rolling load that a Dock Leveler can safely support while in the extended or service position. This dynamic rating should be used when selecting your Dock Leveler, since it is the only method that considers true, live working conditions.

3. Are all Dock Levelers structurally alike? Absolutely not. Even Dock Levelers with the same capacity rating vary greatly in design. The structural integrity of a Dock Leveler, like that of a bridge, is determined not by the top surface, but by the type of reinforcement underneath. The deck supports in general use today range from light gauge formed shapes to structural I beams. A rational comparison is crucial. Remember that a modern Dock Leveler has to be able to withstand the dynamic force of a fully loaded lift truck, constantly hitting it at up to 6 m.p.h. (10 k.p.h.), without the deck dishing. PIONEER uses structural “C” channel as deck support on all of our pit levelers, except the C Series. The C or Contractor series incorporates the same type of deck beam configuration as our competitors.

4. What do you mean by ‘dishing’? Dishing is the term used to describe the condition where a Dock Leveler deck plate, that has inadequate structural support, has distorted. The deck has waves in it that are a clear sign that the steel is dangerously stretched and fatigued. Preventing dishing is the reason why a Dock Leveler’s deck structure, particularly the type, number and placement of beams, is so important.

5. Why is it so important that my Dock Leveler tilt? Many trucks are canted to one side due to unevenly distributed loads, tires that are unevenly inflated or a side to side slope on the drive. Tilt allows a Dock Leveler to compensate for this canted condition. Without tilt, the Dock Leveler lip would not lie flush with the trailer bed. Tilt is most important when a fork lift is backing out of a trailer. Many manufacturers meet the tilt requirement by depending on the ramp to twist under load. However, with this design, when the load passes off the ramp and onto the truck, the ramp and lip will return to their original position. In this condition, the lip creates an obstruction of up to 4″ high (102 mm), and causes severe damage to the fork lift tires, drive train and transmission. The only safe tilt is maintained tilt!

6. Who needs an Edge-of-Dock?

  • those with limited space
  • end users or contractors
  • light to medium loads
  • average to heavy traffic
  • those with a minimum variance between truck bed height and dock height

7. How much lip length is recommended in the truck at all times? It is recommended that 4” to 6” of the lip should remain in contact with the vehicle at all times.

8. How do you determine the capacity of dock levelers? There are three ways of determining the capacity of a dock leveler. The first is static load – the amount of standing (non-moving, non-impact) weight the dock leveler will support. The second factor is rollover capacity – the amount of moving weight the leveler will support in its closed and fully supported position. The third is dynamic load – this is a measure of the force the load applies to the leveler as it impacts the leveler in a raised position. The dynamic rating is a combination of the weight of the lift vehicle and its load, its speed and the angle of the leveler above dock. Dynamic force increases as the grade increases, therefore, a longer dock leveler will handle greater loads, because the dynamic impact is less.

9. What are the advantages of Hot Dip Galvanizing a leveler? Hot Dip Galvanized units have a zinc coating that bonds with the metal itself creating a barrier that is an extension or a part of the metal itself. This process provides a rugged, durable unit, significantly reduces rust and corrosion and extends the life of the product.

This application is ideal for coastal areas, food service industries and chemical/pharmaceutical-type environments. Loading docks in high weather or chemical exposure situations should make this investment. Whether it’s an edge-of-dock, portable board or pit leveler, Hot Dip Galvanizing can be an effective, long term solution.

10. Why should I consider a Versa Panel? Loading docks are becoming busier as well as more and more automated. Increased automation not only calls for multiple control panels, it also dictates more electrical conduit for the electrical wiring as well as various warning and indicator lights. The dock walls around the doors can get extremely congested with various electrical boxes and the wiring to support them. This can cause confusion and lost productivity. On top of all that the installation costs for multiple panels is significantly higher.

The Pioneer Versa Panel can operate the leveler, the truck restraint and the overhead door from one location utilizing one electrical feed. Installation costs are cut dramatically! In addition the convenience of a single location for all of the operations at a dock door can greatly improve productivity on the dock.

For Immediate Service  Call

484 – 415 – 9063